How do you adjust tension on the Jes extender?

[Lyrics]

Hello, I'm new here so if this has been covered already please direct me to the right post.

I got the jes extender two weeks ago. I have figured out how many rods I need to reach just above erect length, thats going fine. I feel a strech so thats good.

The confusing bit is the tension. No matter what I do the 3 lines on the hexagonal bars remain. I have tried adding another rod but this causes slippage as the stretch is too much and it is probably an inch above the erect length.

So I know I have the right amount of rods for my length, so why do the tension lines remain the same? I do feel a good stretch despite not being able to adjust tension. The first line is 900g then 1200g then 1500g. I can see them all so I dont know if that means I'm at 900g?

I currently have two rods attached. I have the hexagonal bars turned to increase length to the max, I also have the screws turned which is where I expected the lines on the hexagonal bars to start disappearing into the springs. I have been compressing the springs when putting the device on and always check they are firmly compressed. When initially pushing the springs onto the bars that is the only time I see the hexagonal lines covered, once the springs come up all lines can be seen.

I have watched various videos and I'm yet to find one where I see the tension lines disappearing into the screens as demonstartes on the computerised image on the jes extender dvd manual.

Can any experienced users maybe shed some light on whats going on here or point me in the direction as to where I can find a video where the tension bars are being adjusted?

Thanks

 

[Dangler]

If you are using the noose tube to fasten in, or the strap can make a difference. The tube can slip easier that the strap.

As long as your dick keeps stretching out, (or there is slippage), as you adjust the extender longer with the adjustments, you can not build up tension.

If you google jes extender and then click Videos in the search results page header, there are ooodles of videos.

It is akin to using a Torque wrench on a nut that keeps turning/moving. You can't build up force/torque until the object (nut) begins to resist the pulling force.

 

[Lyrics]

Yeah, im pretty sure its a faulty product. Its under warranty so will ask to replace or repair

 

[EliteKing07]

Yeah, im pretty sure its a faulty product. Its under warranty so will ask to replace or repair

Anything else that made you come to that conclusion? I have seen MANY posts like this about a lot of devices but have never seen a good answer so can't help you there but can add and say my x4 labs extender seems to have the same thing going on and I really don't think it's a faulty product just that I have no idea how to use it properly.

 

[dodgy]

He says it compresses when he puts it on, so presumably the springs compress and the notches are capable of moving into the correct position, he just doesn't have enough bars on it to have enough adjustment to compress it to the right length for spring compression.

Spring extenders are very difficult to put on, you almost need 3 hands, I don't understand why people use them, a slider extender is so much easier to use.

I would bet most people using spring extenders don't have the correct pressure within 15 minutes of strapping on, no wonder there's so many threads about no gains with extenders.

 

[everydaynormalguy]

He says it compresses when he puts it on, so presumably the springs compress and the notches are capable of moving into the correct position, he just doesn't have enough bars on it to have enough adjustment to compress it to the right length for spring compression.

Spring extenders are very difficult to put on, you almost need 3 hands, I don't understand why people use them, a slider extender is so much easier to use.

I would bet most people using spring extenders don't have the correct pressure within 15 minutes of strapping on, no wonder there's so many threads about no gains with extenders.

Sir,you took the words out of my mouth.Absolutely agree with you.That`s the case probably.I agree with slider extender being way better 100%.

I don`t think that the device is the problem,because if you can compress it with hands and hide the bars,then it`s not the device problem.This kind of extenders just suck.I was able to make the first line almost hide when wearing it but it slipps often anyway.I need to put 6 hours of my day if I want to get 3 hours extending,because half of the times of slippage.

However I can give you two options to try,because you got this device anyway:
-first one is you can try to push the extender base more "under your" with pushing the base of the extender down(digging more into the balls ,pushing the balls back and trying to get the extender as much as you can "under you").The upper side of the base is digging into your upper side of the penis.I don`t know if it clear what I am trying to say,but hope so.The idea of that is to reduce a little bit the difference between your penis size and the lenght of the device and put it on a little easier.When you strap under the glance that way, your balls are going to get sucked into a bit with the penis,so you can pull the balls and take them out of the base,once the strap is attached.
-The other thing you can try is to add smaller rods.You don`t need to buy original rods but you can use this screwable nail ( I don`t know the exact word on English).It looks like a nail but it`s not sharp and it`s screwable.You can find this in every hardware store.You need to find the right size that fit the screws of the extender.That way you can get a little bit more stretch.The good thing about this kind of "rods" is that you can unscrew them a bit with the time and get a little more lenght of the device everytime.They need to be last rods on the device,because you can`t attach another rods from their ends.I am still not sure that the jes extender got the same type of screwable rods as mine so not sure if this is going to work with jes extender.I was using proextender system.