Bathmate questions

lordoftorture

Registered
Well Done !
Joined
Jan 27, 2016
Messages
53
Reaction score
0
Points
0
I have been using X30 for 3 months about 12 minutes a day, 6 days a week. It works better than expected. I have gone from 13cm (5.12") MEG to 14.5cm (5.7") and that is rock hard erection with no swelling. I get additional 0.4" for about 2-3 hours after pump, but it is soft and squishy. Maybe it will get to future gains.
I have two questions:
1. Most of my gains are mid shaft and a little on the head. Base has not moved and is now thinner than the rest of my penis. When I pump I fill up the hole width. I see my skin push against the cylinder and all the pressure is on the top 3rd. Should I get bigger model - X40, even though my length is modest? Is there some upgrade program?
2. Ever since school it has been harder and harder to get an erection. Now I need viagra and a woman I really like. Porn doesnt work for me.
So I have been always starting soft and it gets filled with blood, but I would not call it erection. It looks like sponge - very big, but soft and pointing down. Yesterday I asked my girl to give me a hand and get it in hard. Pressure felt much much stronger. But in the end result was the same. Only difference was my skin was blue which usually doesnt happen.
Is it critical to go in 100% hard, or doesnt matter in the long run?
 

avz

Registered
Well Done !
Joined
Apr 16, 2017
Messages
43
Reaction score
3
Points
0
Location
Albion Britannia
Can't offer expert advice, but I always come out a purple colour, as long as it was a good seal.

I've found that going in somewhat hard seems to give better results. Going in flaccid seems to produce poorer results.

I've also found that the erection in the Batmate seems to be wider, not longer and seems more squishy than hard, but it's hard to tell looking through the plastic. I am 6.5" NBPEL and in the Bathmate the most I've got up to is 6.25", which is probably around 6.5" due to the bellows. When I am up to 6.25" it looks harder, but it's hard to tell.

On the topic of upgrading to the X40: I chose the X40 because I would only have 0.3" of girth play room in the X30. The X40 has 7.75", which I have filled out width-wise but not the whole circumference, but I find it to be a bit cumbersome as it's longer than I need and I think the size of it negatively affects getting a good seal. I am going to look at getting a normal pump.
 

Walter BP Rep

Registered
Well Done !
Joined
May 13, 2015
Messages
2,915
Reaction score
49
Points
68
Location
NJ
I have been using X30 for 3 months about 12 minutes a day, 6 days a week. It works better than expected. I have gone from 13cm (5.12") MEG to 14.5cm (5.7") and that is rock hard erection with no swelling. I get additional 0.4" for about 2-3 hours after pump, but it is soft and squishy. Maybe it will get to future gains.
I have two questions:
1. Most of my gains are mid shaft and a little on the head. Base has not moved and is now thinner than the rest of my penis. When I pump I fill up the hole width. I see my skin push against the cylinder and all the pressure is on the top 3rd. Should I get bigger model - X40, even though my length is modest? Is there some upgrade program?
2. Ever since school it has been harder and harder to get an erection. Now I need viagra and a woman I really like. Porn doesnt work for me.
So I have been always starting soft and it gets filled with blood, but I would not call it erection. It looks like sponge - very big, but soft and pointing down. Yesterday I asked my girl to give me a hand and get it in hard. Pressure felt much much stronger. But in the end result was the same. Only difference was my skin was blue which usually doesnt happen.
Is it critical to go in 100% hard, or doesnt matter in the long run?

If you're not packing the pump then you don't need to get a bigger one. Try wrapping the parts you don't want to isolate before you wrap. This should encourage target expansion. You should start off light with pumping or any other type of training you do. Did you try getting erect before you got into the tube?
 

lordoftorture

Registered
Well Done !
Joined
Jan 27, 2016
Messages
53
Reaction score
0
Points
0
I am filling the tube tight from base to glans. Sometimes even the glans is swollen to the girth of the tube. When I get it out the rubber rings ar imprinted on all sides of my base (I dont use the plastic part). Lengthwise I still have about an inch of free space. Circumference I dont have any more space to expand.
I managed to get it in hard once and the pressure felt much stronger. Like a hard pull from the inside. But the end result was about the same as starting soft.
 
Last edited:

Walter BP Rep

Registered
Well Done !
Joined
May 13, 2015
Messages
2,915
Reaction score
49
Points
68
Location
NJ
I am filling the tube tight from base to glans. Sometimes even the glans is swollen to the girth of the tube. When I get it out the rubber rings ar imprinted on all sides of my base (I dont use the plastic part). Lengthwise I still have about an inch of free space. Circumference I dont have any more space to expand.
I managed to get it in hard once and the pressure felt much stronger. Like a hard pull from the inside. But the end result was about the same as starting soft.

Simply put, you need to get a bigger tube! If it takes you time to fill the first one them pump until you do and then insert yourself into a larger tube for your next phase.